Acti I91 Manual do Utilizador

Indoor PTZ Camera Hardware Manual I91, I92, I912 Ver. 2015/05/28

www.acti.com Hardware Manual 10 Before Installation Unpacking the Camera NOTE: To avoid scratches or leaving fingerprints on the dom

www.acti.com Hardware Manual 11 3. Rotate the dome cover clockwise to attach it. Preparing the Power Adapter In case of using a

www.acti.com Hardware Manual 12 2. Take note that the power adapter cable has two (2) different wires: 3. Connect the wire with t

www.acti.com Hardware Manual 13 Preparing the DI/DO Connector Depending on your surveillance needs, you may connect digital input or

www.acti.com Hardware Manual 14 The table below shows the DI/DO connection specifications: Device DI Connection design TTL - compa

www.acti.com Hardware Manual 15 High Voltage DO Device Connection Even though the camera provides 12V power, this may not be enough

www.acti.com Hardware Manual 16 Installation Procedures There are several mounting options that you can use to install the camera. S

www.acti.com Hardware Manual 17 Straight Wall Mount PMAX-0110 PMAX-0303 (Gooseneck)

www.acti.com Hardware Manual 18 Other Mounting Accessories Accessories PMAX-0702 (Junction Box) PMAX-0104 (Extension Tubes) NO

www.acti.com Hardware Manual 19 Mounting on the Ceiling There are three mounting solutions that you can do to mount the camera on th

www.acti.com Hardware Manual 2 Table of Contents Precautions 4 Safety Instructions ...

www.acti.com Hardware Manual 20 4. Align and attach the fixing bracket to one of the holes on the camera using the supplied screw (

www.acti.com Hardware Manual 21 7. Tighten the screw on the fixing bracket to fix the camera position. This is to avoid accidental

www.acti.com Hardware Manual 22 Using the Flush Mount Use the Flush Mount when installing the camera on a dropped ceiling; there i

www.acti.com Hardware Manual 23 Step 2: Prepare the Flush Mount 1. Push to detach the cover ring from the mount as marked below. T

www.acti.com Hardware Manual 24 Step 4: Install the Mount 1. Insert the metal bracket through the hole until the ring edge is flat

www.acti.com Hardware Manual 25 3. Tighten the screws to secure the mount and make sure the network cable, power adapter, and other

www.acti.com Hardware Manual 26 Step 5: Connect the Cables and Optional Accessories  Insert a memory card into the camera card slo

www.acti.com Hardware Manual 27 2. Slide the camera clockwise to secure the hooks to the mount. Notice that the fixing bracket scre

www.acti.com Hardware Manual 28 Using the Pendant Mount In case of high ceilings, the camera can be lowered by pendant mount. NOTE:

www.acti.com Hardware Manual 29 3. Install the straight tube on the ceiling. NOTE: If the straight tube is not long enough, you ma

www.acti.com Hardware Manual 3 Access the Camera ... 41

www.acti.com Hardware Manual 30 3. Twist the mount kit to align the screw holes and attach the two (2) mounting screws (included in

www.acti.com Hardware Manual 31 3. Slide the camera counter-clockwise to secure the hooks to the mount. 4. On the top of the moun

www.acti.com Hardware Manual 32 Mounting on Straight Wall There are four (4) mounting solutions that you can do to mount the camera

www.acti.com Hardware Manual 33 2b. If the cable will go along the wall, remove the pre-cut tab on the L-type wall mount using p

www.acti.com Hardware Manual 34 2. Align and insert the camera base hooks to the mounting holes. 3. Slide the camera clockwise to

www.acti.com Hardware Manual 35 Other Accessories and Adjustments How to Replace the Dome Cover Depending on your surveillance needs

www.acti.com Hardware Manual 36 How to Reset the Camera A reset may be necessary if the following instances happen:  The administr

www.acti.com Hardware Manual 37 Accessing Camera Configure the IP Addresses In order to be able to communicate with the camera from

www.acti.com Hardware Manual 38 When the left mouse is clicked on the camera model name, the default browser of the PC is automatica

www.acti.com Hardware Manual 39 Use the default IP address of the camera If there is no DHCP server in the given network, the user m

www.acti.com Hardware Manual 4 Precautions Read these instructions Read all the safety and operating instructions before using this

www.acti.com Hardware Manual 40 Manually adjust the IP addresses of multiple cameras If there are more than one camera to be used in

www.acti.com Hardware Manual 41 Access the Camera Now that the camera and the PC both have their unique IP addresses and are under t

www.acti.com Hardware Manual 42 The examples in this manual are based on Internet Explorer browser in order to cover all functions o

Copyright © 2015, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu Dis

www.acti.com Hardware Manual 5 Federal Communications Commission Statement This equipment has been tested and found to comply with t

www.acti.com Hardware Manual 6 Safety Instructions Don’t use the power supply with other voltages This device is likely to be damage

www.acti.com Hardware Manual 7 Introduction List of Models This hardware manual contains the following models: I91 1MP Indoor PTZ w

www.acti.com Hardware Manual 8 Package Contents Camera Power Adapter Universal Plug Converter Surface Mount Mounting Screw Kit F

www.acti.com Hardware Manual 9 Physical Description Connectors View Internal View Item Descrip