ACTi B94 Manual

Outdoor Mini PTZ Series Hardware Manual B94, B95, B96, B97 2014/08/06

www.acti.com Hardware Manual 10 4) Digital Input / Output (DI/DO) and Audio Input / Output This connector connects to digital input

www.acti.com Hardware Manual 11 Mounting Options There are several mounting options that you can use to install the camera. Select t

www.acti.com Hardware Manual 12 Mount Types Accessories Straight Wall Mount Suitable when mounting the camera on straight walls. P

www.acti.com Hardware Manual 13 Other Mounting Accessories Accessories PMAX-0104 (Extension Tube) PMAX-0702 (Junction Box) NOTE:

www.acti.com Hardware Manual 14 Installing the Camera on a Surface This section describes the procedures in installing the camera on

www.acti.com Hardware Manual 15 Step 2: Open the Dome Cover NOTE: To avoid scratches or leaving fingerprints on the dome cover, it i

www.acti.com Hardware Manual 16 4. Remove the two (2) desiccant bags protecting the camera lens. NOTE: A small desiccant bag i

www.acti.com Hardware Manual 17 Step 3: Prepare for Waterproof and Connect the Cable The camera comes with two (2) glands used for w

www.acti.com Hardware Manual 18 Waterproof Solution with Naked Cable This section describes the procedures in using the bundled cabl

www.acti.com Hardware Manual 19 4. Attach the cable gland body to the hole of the camera. Attach to Camera Side Hole

www.acti.com Hardware Manual 2 Table of Contents Precautions ... 4 Safety

www.acti.com Hardware Manual 20 6. Insert the sealing insert with claw into the cable gland body and then attach the clamping nut t

www.acti.com Hardware Manual 21 Waterproof Solution with Conduit This section describes the procedures to waterproof the cabling con

www.acti.com Hardware Manual 22 2. Disassemble the bundled conduit gland as shown below: NOTE: In this installation, the conduit g

www.acti.com Hardware Manual 23 5. Insert the sealing insert and attach it at the end of the flex conduit. 6. Screw the co

www.acti.com Hardware Manual 24 b. Insert the sealing insert into the conduit gland body and then attach the clamping nut as t

www.acti.com Hardware Manual 25 10. Connect the network cable to the Ethernet port and other cables (if any) to the corresponding co

www.acti.com Hardware Manual 26 Step 4: Install the Camera to the Surface Align the camera screw holes and the cable hole (if necess

www.acti.com Hardware Manual 27 2. Remove the plastic covering the dome cover. Final installation will look like the illustration b

www.acti.com Hardware Manual 28 Other Connections This section describes the procedures in preparing the external devices that you c

www.acti.com Hardware Manual 29 4. Tighten the screws of the 12V pin and the GND pins to secure the wire connection. 5. Set

www.acti.com Hardware Manual 3 Other Adjustments and Accessories ... 34 How to Remove / Install the Camera Module...

www.acti.com Hardware Manual 30 Connecting the DI/DO and Audio Devices (Optional) Depending on your surveillance needs, you may conn

www.acti.com Hardware Manual 31 The table below shows the DI/DO connection specifications: Device DI Connection design TTL - compat

www.acti.com Hardware Manual 32 High Voltage DO Device Connection Even though the camera provides 12V power, this may not be enough

www.acti.com Hardware Manual 33 How to Connect Audio Devices Audio input / output devices, such as an active microphone or speaker c

www.acti.com Hardware Manual 34 Other Adjustments and Accessories How to Remove / Install the Camera Module How to Remove the Camera

www.acti.com Hardware Manual 35 How to Install the Camera Module 1. Align the camera module to the guides on the housing. 2.

www.acti.com Hardware Manual 36 How to Replace the Dome Cover For more discrete surveillance needs, the bundled dome cover can be re

www.acti.com Hardware Manual 37 4. Remove dome cover from the cover housing. 5. Remove the rubber from the dome cover. 6. Inser

www.acti.com Hardware Manual 38 8. There are 3 indents on the cover housing; note the indent (a) which is on the center of the exte

www.acti.com Hardware Manual 39 10. Fit the screw into the spring wire that is attached to the camera. Note the screw placement as s

www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before

www.acti.com Hardware Manual 40 How to Insert / Remove a Memory Card The camera supports local video recording or saving of snapshot

www.acti.com Hardware Manual 41 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera f

www.acti.com Hardware Manual 42 Double-click on the camera model name, the default browser of the PC is automatically launched and

www.acti.com Hardware Manual 43 Use the default IP address of a camera: If there is no DHCP server in the given network, the user ma

www.acti.com Hardware Manual 44 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in

www.acti.com Hardware Manual 45 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are u

www.acti.com Hardware Manual 46 Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser

Copyright © 2014, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu Dist

www.acti.com Hardware Manual 5 Federal Communications Commission Statement This equipment has been tested and found to comply with t

www.acti.com Hardware Manual 6 Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. At

www.acti.com Hardware Manual 7 Introduction The List of Models This hardware manual contains the following models: B94 1.3MP Outdoo

www.acti.com Hardware Manual 8 Package Contents Camera Mounting Screw Kit Hexagon Screwdriver Drill Template Conduit Gland Cable

www.acti.com Hardware Manual 9 Physical Description Below is an illustration of the camera module. 1) Ethernet Port Connects to a